pro2_av2_cp2_cp2e_rack2_pac2_4.003.0015.txt
MC2W) and ID transmitter should work.
- Now handle overflows in the Serial Pacer.
- Made speed improvements for event scheduling (ramps and OSCs) in systems
with many Simpl+ modules.
- Fixed the DUPLE and UNDUPLE symbols.
- Fixed a problem with the Serial Demultiplexor Special (SMRX) symbol where
only the first decode worked.
- Fixed Poll Accelerator support so that CT1000 upload will work. REQUIRES
VERSION 3.105 OF THE POLL ACCELERATOR FIRMWARE.
- Fixed a bug in Simpl+ that occurred with multiple instances of the same
Simpl+ module where "0s" characters would appear in generated strings. The fix
now limits the length of a format specifier to 256 characters. If the format
specifier is too long, an error message will be generated.
- Fixed a problem with restarting programs where Wait Events were not being
terminated. (issue w/program with waits in waits - when stopprogram issued,
the wait was attempting to get WaitList semaphore, which couldn't be obtained
because of destruction, which caused a deadlock.)
- Support Stack checking for Simpl+ modules.
- If a bad time is passed to the system, all the time fields are placed in the
error message.
- Fixed a bug in restarting a program that caused TestManager to miss signals
at program startup when connected to the system via Ethernet.
Build: 3.088(Release)
Oct 10, 2003
- Full support for the C2VEQ-4 plug-in card.
- Fix issue if DHCP is on and IP Address of Lan A is 0.0.0.0, the status
of Lan B would be printed on doing an ESTATUS.
- Fix lockup issue if an Ethernet link is lost.
- Fix program termination issue (i.e. Hitting F10) if a Gateway node
is still active (i.e. you have a web page open to an IP ID that is in
the IP table & registered in the program, an e-Power App connection,
etc.) that would reboot the processor.
- Fix reporting of CTS status from 2 Series processors configured as slaves.
- Removed the warning that occurred during NVRAM auto-compaction. Only an error
is posted if the auto-compaction fails.
- Fixed an issue with the NAT configuration pages where after applying portmap
changes, the display does not show all the changes.
- Relaxed the Cresnet timing in the CLW dimmers to compensate for the dimmers
not conforming to specification.
- Modify SDLY so that its message would be seen by all consoles.
- Fixed a bug in where empty Zbus slots were reporting as unknown instead of
empty
- Fixed a problem with the NAT in which the addition of a portmap with ext
port LESS than int port worked, but failed to remove without error notice and
then the same port could not be added again.
- Fixed issues where webserver redirection was not correct.
- Changed trilist to allow serial strings that are permanent & empty to be
re-transmitted on an update request. Trilist affects many symbols - all
touchpanels & ethernet ISC are the biggest ones.
- Improved the Ethernet driver to detect and recover from conditions that could
disable the transmitter.
- Fixed a crash when an empty file spec was passed to the Simpl+ FileDelete()
function.
- Support for new Simpl+ function WaitForInitializationComplete(). This will
pause the processing in Main() until the logic has been complete initialized.
(The 1 logic solution is complete.) This will require SIMPL Windows
v2.05.06 or later.
- Fixed a crash seen with program file names that exceeded 124 characters on
the internal flash. The name is now clipped to 124 and the file is
ignored. The net result is that the program is not loaded and an error
Page 9
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais